FANUC Arc Welding Robots | Maintenance and Servicing


FANUC Arc Welding Robots | Maintenance and Servicing

 

Regular maintenance of robots can extend their lifespan. FANUC robots have maintenance cycles of three months, six months, one year, and three years.

 

The details are as follows:

 

The following describes in detail how to replace the battery and lubricant.

1. Replace the battery

During maintenance of a FANUC robot system, two types of batteries need to be replaced: the battery on the controller's main board and the battery on the robot body.

1.1Replace the battery on the controller mainboard

Programs and system variables are stored in the SRAM on the mainboard, which is powered by an onboard lithium battery to ensure data retention. If the battery voltage drops too low, an alarm (SYST-035: Low or No Battery Power in PSU) will appear on the Teach Pendant (TP). Should the voltage fall further, the contents of the SRAM can no longer be maintained; in this case, the battery must be replaced, and the previously backed-up data must be reloaded. Therefore, it is important to regularly back up your data using a memory card or floppy disk. It is recommended to replace the battery on the controller mainboard every one to two years.

The procedure is as follows:

1) Prepare a new lithium battery (FANUC original battery is recommended).

2) After the robot is powered on and starts up normally, wait 30 seconds.

3) Power off the robot, open the controller cabinet, unplug the connector, and remove the old battery from the main board.

4) Install the new battery and plug in the connector.

5) The battery replacement process must be completed within 20 minutes.

 

1.2 Replace the battery on the robot body

The battery located on the robot unit is used to retain data from the encoders on each axis. Consequently, the battery must be replaced annually. When a low-battery voltage warning—specifically the "SRVO-065 BLAL alarm (Group: %d Axis: %d)"—occurs, the user should replace the battery. If it is not replaced in a timely manner, an "SRVO-062 BZAL alarm (Group: %d Axis: %d)" will be triggered, rendering the robot inoperable. Should this occur, the battery must be replaced, and a "mastering" procedure must also be performed to restore the robot to normal operation.

The procedure is as follows:

1) Keep the robot powered on and press the emergency stop button.

2) Open the battery compartment cover and remove the old battery.

3) Install a new battery (using an original FANUC battery is recommended), ensuring the positive and negative terminals are oriented correctly (refer to the markings on the battery compartment cover).

4) Close the battery box cover and tighten the screws.

 

 

2. Change the lubricating oil

For every three years of operation or 10,000 hours of service, the lubricating oil in the reducers for axes J1, J2, J3, J4, J5, and J6, as well as the oil in the J4-axis gear box, must be replaced. For certain robot models—such as the S-430 and R-2000 series—the lubricant for the counterbalance (balance weight) bearings must also be replaced every six months or 1,920 hours of operation.

2.1 Replace the lubricating oil in the reducer and gear box

The procedure is as follows:

1) Power off the robot.

2) Remove the plug from the oil outlet.

3) Add lubricating oil through the oil inlet until fresh lubricant begins to flow out from the oil outlet; then, stop adding oil.

4) Operate the robot so that the axis being lubricated moves repeatedly for a period of time, until no more oil flows out from the oil outlet.

5) Reinstall the plug on the oil outlet.

 

Note: Improper handling may result in damage to the seal ring. To avoid such errors, operators should take the following points into consideration:

1) Before replacing the lubricating oil, remove the plug from the oil outlet.

2) Add the oil slowly using a manual grease gun.

3) Avoid using factory-supplied compressed air as a power source for the grease gun. If it must be used, the pressure must be kept below 75 kgf/cm², and the flow rate must not exceed 15/ss.

4) Use only the specified lubricating oil; the use of any other type may damage the speed reducer.

5) Once the replacement is complete, ensure that no lubricating oil is leaking from the outlet, then reinstall the oil outlet plug.

6) To prevent slipping accidents, thoroughly clean any traces of oil from the robot and the floor.

 

2.2 Replace the lubricating oil for the balance weight bearings

The procedure is as follows:

Add lubricant directly through the oiling port; there is no need to use a large amount each time (approximately 10 cc).

For the required quantity of lubricating oil and the locations of the oil fill and drain ports, please refer to the mechanical maintenance manual provided with the equipment.

 

Note: All content is for learning and communication purposes only. Replacing batteries and lubricants must be done by professional technicians. Original batteries and lubricants must be used; otherwise, you will be responsible for the consequences.

 

 

 

 

———————— END ————————